ผลการค้นหา

คำศัพท์/สำนวน บทความ  หาอะไรก็เจอ!
ค้นเจอ 54 รายการ

 หรือคุณกำลังค้นหา Backwardation, Back End, usually, Bismuth, Slip Form, Blister, Pin support:

big earthen jar (usually for water)

แปลว่าโอ่งน้ำ

N
 EN-TH Dictionary

Bloom 2

แปลว่า(english) A semi-finished hot rolled product, rectangular in cross section, produced on a blooming mill. For iron and steel, the width is not more than twice the thickness, and the cross-sectional area is usually not less than 36 sq. in. Iron and steel blooms are sometimes made by forging.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

BLADDER

แปลว่า(english) A separator or diaphragm usually found in a chamber to facilitate separation of two (2) fluids or gases.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

Black Oil Tempered Spring Steel Strip (Scaleless Blue)

แปลว่า(english) A flat cold rolled usually .70/.80 medium high carbon steel strip, blue-black in color, which has been quenched in oil and drawn to desired hardness. While it looks and acts much like blue tempered spring steel and carries a Rockwell hardness of C44/47, it has not been polished and is lower in carbon content. Used for less exacting requirements than clock spring steel, such as snaps, lock springs, hold down springs, trap springs, etc. It will take a more severe bend before fracture than will clock spring, but it does not have the same degree of spring-back.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

Acid Process 2

แปลว่า(english) A steel making method using an acid refractory-lined (usually silica) furnace. Neither sulfur or phosphorus is removed.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

Blow Back

แปลว่า(english) A coating defect consisting of a lower coating film weight on the bottom of the coated sheet caused by high velocity air in the oven. Blow back usually occurs with high solids coatings which have little solvent to evaporate and "set" the film.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

Bearing Load

แปลว่า(english) A compressive load supported by a member, usually a tube or collar, along a line where contact is made with a pin, rivet, axle, or shaft.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

Billet

แปลว่า(english) (1) A semi-finished section hot rolled from a metal ingot, with a rectangular cross section usually ranging from 16 to 36 in., the width being less than twice the thickness. Where the cross section exceeds 36 in., the term “bloom” is properly but not universally used. Sizes smaller than 16 in. are usually termed “bars”; a solid semi-finished round or square product which has been hot worked by forging, rolling, or extrusion. (2) A semi-finished, cogged, hot rolled or continuous-cast metal product of uniform section, usually rectangular with radiused corners. Billets are relatively larger than bars.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

Bell Mouth

แปลว่า(english) The flaring or tapering of a machined hole, usually made at the entrance end because of misalignment or spring of the cutting tool.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

Blush

แปลว่า(english) A coating defect consisting of the whitening of a cured film which results in a translucent or opaque appearance with accompanying loss of gloss. Blushing usually occurs during the pasteurization or steam processing of films which are undercured or water sensitive.
 ศัพท์ช่างภาษาอังกฤษ – ไทย

Usually

กริยาช่อง 2คำว่า Usually ไม่ใช่คำกริยา
 กริยา 3 ช่อง

usually

แปลว่าตามธรรมดา

ADV
 EN-TH Dictionary